This is an index of edge tools for sale. Some of them will have a button to click to see a Picture. ... Instead of having to load each image to continue, just scroll this list and click to see an image. This is a list of tools for sale, which for various reasons are good deals.

Note: I have a Tool Order Form that goes through a secure server and will be encrypted when you return it. So, it is safe to give credit card information. Just click on Click To Order in any section, or right here.

Back To Tool Index Back to Homepage

1. STANLEY NO. 7C, JOINTER PLANE, Notched-rectangle logo on the cutter with 1 1/2 inches of meat left. The body has been cleaned and repainted. The ebonized (black) handle and tall knob have some missing finish. The Stanley cap looks like it is recent. A great user, G+ ...... $70.00
   Picture

2. STANLEY NO. 18, BLOCK PLANE, 6 inches long, with adjustable throat. Nickeled trimmings. Early J trademark on the cutter, and STANLEY and the Dec, 28, (18)86 logo on the knuckle-joint cap. 80% japanning, and almost no nickel plating, G+ .......... $35.00
   Picture

4. STANLEY NO. 15, 7 INCH BLOCK PLANE, with adjustable throat. Same as the No. 9 1/2, but an inch longer. Notched-rectangle logo on the cutter. 80% japanning with a little dirt. One side of the bottom has been rounded a bit, I don't know why, but it won't effect use. Owner's initials on the sides, G+ ........... $40.00
   Picture
   
   Picture - Bottom

6. STANLEY NO. 9 1/2, BLOCK PLANE, An early Excelsior model from around 1895. Adjustable throat. J trademark on the cutter with good length. It has been cleaned and repainted. It had a chip on the top front of the right side that has been repaired with JB Weld. A good, clean user, G .......... $30.00
   Picture

7. STANLEY NO. 130, DOUBLE-END BLOCK PLANE, 7 3/4 inches long. One side is a regular block plane, the other is a bull-nose. An early one with curved sides and the 1883 aptent dates on the cutter. 85% of the japanning remains (the picture looks like it was repainted, but, it's not. There is a 1/4 inch chip in top of the front rail. I can't tell if it was a casting flaw or not. In any case, this is an early plane in very nice condition, G+ .......... $35.00
   Picture

8. SARGENT NO. 306, BLOCK PLANE, 6 inches long - like a Stanley No. 9 1/2 but with nickel plated trimmings. Has a Craftsman blade,(which is missing the little lateral-adjust lever) so, it was probably sold by Sears. 95% japanning, pretty good nickel plating, G++ .......... $45.00
   Picture

1. FERNHURST SPIRAL RATCHET SCREWDRIVER. This is the same as the Yankee No. 130. Has a spring-return, and all three bits. In the original box, Fine ........ $30.00
   Picture

2. BUELL BRO. TOOL HANDLE, Beech handle with six tools. The ferrule has a split that doesn't effect use, G+ ............ $20.00
   See Picture

3. J. S. FRAY & CO. TOOL HANDLE, Rosewood tool handle with six bits. The top was split apart and reglued, G ........... $20.00
   See Picture

4. STANLEY NO. 62 1/2 RULE. (narrower than the No. 62) Sweetheart logo. Two-foot, Four-fold, full brass bound. It is dirty and somewhat worn on the outside, but pretty nice inside, which is the side you will measure from. It could use a bit of cleaning. A rule-collector has recommended using waterless hand cleaner. Slightly sprung, G ........ $15.00
   Picture

5. STANLEY NO. 84 RULE. Earlier S. R & L Co. logo inside. Two-foot, Four-fold, half brass bound (not the inside edges). It is dirty and somewhat worn on the outside, but pretty nice inside, which is the side you will measure from. It could use a bit of cleaning. A rule-collector has recommended using waterless hand cleaner, G ........ $20.00
   Picture

6. BEVEL SQUARE, 10 inch Sliding T bevel, Beech handle, brass trim. Marked only Made in USA, G+ ........... $12.00
   Picture

Back to Homepage Back To Tool Index